Product ID:ALKYD RESIN, VARNISH
MSDS Date:07/31/1987
FSC:8010
NIIN:00-180-6343
MSDS Number: BHBZV

FARWEST PAINT MANUFACTURING CO.

4522 S. 133RD ST
TUKWILA, WA 98168
US

Emergency Phone: (206) 941-1619

Info Phone: (206) 244-8844

Cage: 2F266

FARWEST PAINT MANUFACTURING CO

TUKWILA, WA 98168 US

Telephone: 206-244-8844

Cage: 6F266

RESIN/VEHICLE (VAPOR PRESSURE 2.0 MMHG @ 68F)

Fraction By Weight: 48-53%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM

MINERAL SPIRITS (VAPOR PRESSURE 2.0 MMHG @ 68F)

Fraction By Weight: 45-50%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM

2-BUTOXYETHANOL

CAS: 111-76-2

RTECS: KJ8575000

Fraction By Weight: 2-7%

OSHA PEL S, 50 PPM

ACGIH TLV: S, 25 PPM; 9293

METAL SOAP DRIES (VAPOR PRESSURE 2.0 MMHG @ 68F)

Fraction By Weight: <1%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM

SURFACTANTS

Fraction By Weight: <25%

Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Effects of Overexposure:EYES:SEVERE IRRITATION,REDNESS,TEARING,BLURRED
VISION. SKIN:PROLONGED/REPEATED CONTACT CAN CAUSE MODERATE
IRRITATION,DEFATTING,DERMATITIS. BREATHING:EXCESSIVE INHALATION OF
VAPORS CAN CAUSE NASAL & RE SPIRATORY
IRRITATION,DIZZINESS,WEAKNESS,FATIGUE,NAUSEA,HEADACHE,POSSIBLE
UNCONSCIOUSNESS EVEN ASPHYXIATION.
Medical Cond Aggravated by Exposure:SWALLOWING CAN CAUSE
GASTROINTESTINAL IRRITATION NAUSEA,VOMITING AND DIARRHEA,
ASPIRATION OF MATERIAL INTO THE LUNGS CAN CAUSE CHEMICAL
PNEUMONITIS WHICH CAN BE FATAL.

First Aid:SKIN:THOROUGHLY WASH EXPOSED AREA W/SOAP & WATER. REMOVE
CONTAMINATED CLOTHING,LAUNDER CONTAMINATED CLOTHING BEFORE
REUSE.EYES:FLUSH W/LARGE AMOUNTS OF WATER,LIFTING EYELIDS OFTEN,GET
MEDICAL ATTENTIO N. SWALLOWING:DONOT INDUCE VOMITING,KEEP PERSON
WARM,QUIET & GET MEDICAL ATTN. INHALATION:IF AFFECTED,REMOVE PERSON
TO FRESH AIR. DIFFICULT BREATHING,GIVE OXYGEN.BREATHING
STOPPED,ARTIFICAL RESP.

Flash Point Method:TCC
Flash Point:108F/42.2C
Lower Limits:1.0
Extinguishing Media:FOAM,CO2,DRY CHEMICAL.
Fire Fighting Procedures:SELF-CONTAINED BREATHING APPARATUS WITH A FULL
FACEPIECE OPERATED IN PRESSURE DEMAND OR OTHER POSITIVE PRESSURE
MODE.
Unusual Fire/Explosion Hazard:NEVER USE NEAR OR AROUND WELDERS OR
CUTTING TORCHES,DRUM (EVEN EMPTY) BECAUSE PRODUCT (EVEN JUST
RESIDUE) CAN IGNITE EXPLOSIVELY.

Spill Release Procedures:SMALL SPILL:ABSORB LIQUID ON PAPER,
VERMICULITE, FLOOR ABSORBENT. LGE SPILL:ELIMINATE ALL IGNITION
SOURCES.PERSONS NOT WEARING PROTECTIVE EQUIPMENT ARE EXCLUDED FROM
AREA UNTIL CLEANUP COMPLETED.PREVE NT RUN. IF RUNOFF NOTIFY PROPER
AUTHORITIES.

Handling and Storage Precautions:RESPIRATORY PROTECTION: IF TLV
EXCEEDED A NIOSH/MSHA APPROVED AIR SUPPLIED RESPIRATOR IS
ADVISED.ENGR/ADMINISTRATIVE CONTROLS SHOULD BE IMPLEMENTED.
Other Precautions:CONTAINERS OF THIS MATERIAL MAY BE HAZARDOUS WHEN
EMPTIED, SINCE EMPTY CONTAINERS RETAIN PRODUCT RESIDUES (VAPOR,
LIQUID, AND/OR SOLID)ALL HAZARD PRECAUTIONS GIVEN IN DATA SHEET
MUST BE OBSERVED.

Respiratory Protection:IF TLV OF PRODUCT OR ANY COMPONENT IS EXCEEDED,
A NIOSH/MSHA JOINTLY APPROVED AIR SUPPLIED RESPIRATOR IS ADVISED IN
ABSENCE OF PROPER ENVIRONMENTAL CONTROL OSHA REG ALSO PERMIT OTHER
NIOSH/MSHA RESPIR ATORS UNDER SPECIFIED CONDITIONS.
Ventilation:PROVIDE SUFFICIENT MECHANICAL (GENERAL AND/OR LOCAL
EXHAUST) VENTILATION TO MAINTAIN EXPOSURE BELOW TLV(S).
Protective Gloves:RESISTANT GLOVES SUCH AS NITRILE RUBBER.
Eye Protection:CHEMICAL SPLASH GOGGLES RECOMMENDED.
Other Protective Equipment:TO PREVENT REPEATED OR PROLONGED SKIN
CONTACT, WEAR IMPERVIOUS CLOTHING AND BOOTS.
Work Hygienic Practices:KEEP WORK AREA CLEAN AND FREE FROM LEAKS AND
SPILLS. WASH HANDS THOROUGHLY W/SOAP & WATER BEFORE HANDLING FOOD &
DRINK.
Supplemental Safety and Health
ENGINEERING OR ADMINISTRATIVE CONTROLS SHOULD BE IMPLEMENTED TO REDUCE
EXPOSURE.

Boiling Pt:B.P. Text:300F
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NIL
Appearance and Odor:TRANSLUCENT GREEN THIN LIQUID WITH A MILD SWEET
AROMATIC ODOR.
Percent Volatiles by Volume:56.72

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:KEEP AWAY FROM OPEN FLAMES,SPARKS AND
HEAT. DO NOT WELD NEAR OR AROUND PRODUCT.
Conditions to Avoid Polymerization:KEEP AWAY FROM OPEN FLAMES, SPARKS,
AND HEAT. DO NOT WELD NEAR OR AROUND PRODUCT.

Waste Disposal Methods:DESTROY BY LIQUID INCINERATION, CONTAMINATED
ABSORBENT MAY BE DEPOSITED IN A LANDFILL IN ACCORDANCE WITH
LOCAL,STATE AND FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.